JDownloader Community - Appwork GmbH
 

Closed Thread
 
Thread Tools Display Modes
  #1  
Old 23.04.2010, 10:42
drbits's Avatar
drbits drbits is offline
JD English Support (inactive)
 
Join Date: Sep 2009
Location: Physically in Los Angeles, CA, USA
Posts: 4,437
Exclamation Getting started with Reconnection | Erste Schritte zum Reconnect

Die deutsche Anleitung befindet sich im 2. Beitrag.

Reconnection is an advanced approach for skipping long waits (> 15 minutes) that some hosts impose on free users. It is not helpful while using a premium account. It is not necessary, just another way to increase download speed. It is often more helpful to diversify the hosts you download from.

Please read the whole category before following the instructions of the respective category.

A) Getting Started

If the "Settings" tab does not show in JDownloader, use File - View Settings to make it visible.

On the Settings tab, there is a tree on the left to allow you to select the specific settings you want to work with. You should see Reconnection; click on it. Now, on the right hand side, you should see a tab marked "LiveHeader/Curl". Click on the tab to make sure that page is selected.

From the user manual for your router, find the username, password, and Local IP address of your router. Enter that information into the top of the LiveHeader/Curl page (if your router does not use a username, then just enter your first name as the username). Also, find the name, model, and firmware version (see below) of your router (do not worry if some of this is missing).

If you start your Browser and enter the Local IP address into the address bar, your browser should open a page and show you simple details like the name, model, and firmware version of your router (write down this information). If the Local IP address does not work, use the "Fetch Router IP" button to find the correct IP address (do not forget to record this in the manual).

Note: If you own a Fritz! Box as router, then you can easily type in "fritz.box" in the browser's adress bar to get to the router's page.

B) See if you have a dynamic IP adress that is easily reset

Enter "whatismyip.com" in your browser's address bar and press Enter. This will display your IP address (as the internet sees it). Write down this address.

Now turn the power switch on the Router off, wait about 5 seconds, and turn the power switch back on (if you cannot find a power switch, unplug the power (mains) and plug it back in).

Wait for the internet connection to rebuild (about 2 minutes, Icon in the info tray). Now, reload your browser's web page (usually F5, or click in the address bar and press enter again). If you see a different IP address displayed, then you have a dynamic IP address and can go on to C).

If the IP address does not change, you either have a static IP address or a sticky IP address. Check with your internet provider to make sure you have a Dynamic IP address. If you are supposed to have a static IP address, then reconnection won't work for you.

If you are supposed to have a dynamic IP address (it is sticky), use Google to search for
Code:
site:jdownloader.org change mac address
Read articles like "How to change IP when reconnect doesn't work". Read the related threads. Try those approaches. If none of them work, go to G) If nothing Works.
C) See if there is already information about your Router

Search the Reconnection forum for your router model. Somebody may have found a unique problem reconnecting your router and there may be an answer. The Google search below is for Microlink brand routers; substitute your brand or model:
Code:
site:jdownloader.org "change IP" OR reconnect Microlink
D) See if there is already a script for your Router

You can click on the Select Router button and a window will pop up listing over a thousand routers -- do not panic. At the top of the window is a single line that usually contains "Search Router Model". Enter the model of your router into the line and the list will shorten to a more manageable size. The more information you enter, the shorter the list will get.

Find the listing that most closely matches your Router. Click on the router name and the script will appear in the box on the right. Don't worry if you don't understand it. Click "OK" and the script will be installed for you to use.

Test your script by pressing the Change IP button at the bottom of the page. If it succeeds, congratulations. You now have a working reconnection script.

If it does not succeed, do not give up hope. There are a lot of things to try.

The first thing to try is to click on Reconnect - Advanced in the settings tree on the left. Change the last line (Timeout for IP Change) to 180 (3 minutes). This should allow your router plenty of time to complete a reconnection. This setting can be higher, it just means that you will have to wait longer for tests that fail. It won't affect normal Reconnections unless it is too short. After giving your router more time, go back to the Reconnection page and click on Change IP to test the router.

If the script still does not work, go back to step D) and try a different router script. You may have to try several router scripts before you find the correct script.

E) What if nothing matches my Router or none of the scripts work?

Please watch **External links are only visible to Support Staff**this video about how to Create a Reconnection Script.
To summarize the video, the steps are:
1. Enter the Router's Local IP address into the browser's address bar and press Enter. Your browser will display the router's introduction page, which should include a menu of some kind.
2. Search through the pages, without changing anything. At some point you will probably have to enter your username and password (some routers do not use a username). Look around until you find either a "Restart", "Reboot", "Reset", "Change IP", or "Connection Test" button or link.
3. Open JDownloader Settings - Reconnection. Click on the "Create Reconnection Script" button in JDownloader. Click on the "Start" button. Now, your Browser will navigate to the router's introduction page.
4. Navigate to the Reboot or Restart button or link and click on the button or link. JDownloader has been recording everything you have done since pressing Start. After the router has reconnected, JDownloader will notice the changed IP address and congratulate you on your successful script.
5. Click the "Yes" button to save the reconnection script.
6. Use the "Change IP" button on the bottom of the page in the JDownloader to test your script. If the script works, congratulations! You have a working reconnection script. At a later date, you may be asked for permission to include your script in the database for other users.

Reference: Reconnect Recorder

F) My reconnection script didn't work, what do I do?

1. Don't panic, we have more options.
2. Try part E again, but this time when presented with the Start button, tick the "Raw Mode" check box. This will create a more detailed script that almost always works.

G) If Nothing Works

Rule: Search Before Asking or Creating a New Thread
Searching JDownloader.org
If that does not work, create a new thread in the Reconnect forum, choose the prefix [Script request] and title your thread corresponding to your router name. Describe your router and what you have tried so far. A support person or another user will answer your request as soon as possible.


D-Link router users: Some D-Link routers require an external program to reconnect. See Instructions for Special Routers.

Last edited by Think3r; 18.11.2011 at 11:51. Reason: Prefix Update
  #2  
Old 22.05.2010, 19:32
Think3r's Avatar
Think3r Think3r is offline
Community Manager & Admin (inaktiv)
 
Join Date: Apr 2009
Posts: 3,743
Default

Der Reconnect ermöglicht das Überspringen längerer Wartezeiten, die Free Usern durch die meisten Hoster aufgezwungen werden. Im Grunde genommen stellt er nur ein weiteres Hilfsmittel zur Beschleunigung der Downloads dar, behindert allerdings den wesentlich schnelleren Download beim Verwenden eines Premium Accounts. In diesem Fall ist es hilfreicher, verschiedene Hoster zu verwenden.

Lies bitte zuerst die gesamte Kategorie, bevor Du die Anleitungen der jeweiligen Kategorie befolgst.

A) Allgemeines

Sollte der Einstellungen-Tab nicht sichtbar sein, gehe auf Datei -->Zeige Einstellungen.

Unter Einstellungen -->Module findest Du den Eintrag "Reconnect". Klicke im Reconnect-Tab auf den Reiter "LiveHeader/Curl".

Aus der Benutzeranleitung für Deinen Router musst Du nun den Benutzernamen, das dazugehörige Passwort sowie die lokale IP-Adresse Deines Routers heraussuchen. Gebe diese Informationen im oben erwähnten Reiter ein (sollte Dein Router keinen Benutzernamen haben, gebe einfach einen beliebigen Nicknamen ein). Informiere Dich auch über den Namen, Modell sowie die Firmware-Version (siehe unten) Deines Routers (es ist nicht schlimm, wenn Teile davon fehlen).

Wenn Du Deinen Browser startest und die lokale IP-Adresse des Routers in die Adressleiste eingibst und bestätigst, sollte Dein Browser Dir einfache Informationen wie den Namen, Modell und Firmware-Version Deines Routers anzeigen (schreibe diese Informationen auf). Sollte die lokale IP-Adresse nicht funktionieren, benutze den "Router IP ermitteln" - Button, um die korrekte IP-Adresse herauszufinden (vergiss nicht, die IP einzutragen).

Anmerkung: Solltest Du eine Fritz! Box als Router haben, genügt es "fritz.box" in die Browser-Adressleiste einzugeben, um zur Router-Seite zu gelangen.

B) Überprüfe, ob Du eine dynamische IP-Adresse besitzt


Gebe "wieistmeineip.de" in die Browser-Adressleiste ein, woraufhin Dir Deine IP-Adresse (so, wie das Internet sie sieht) angezeigt wird. Vermerke Dir auch diese.

Schalte nun den Router aus, indem Du den Schalter am Router auf "Aus/Off" stellst oder diesen von der Stromversorgung trennst. Warte 5 Sekunden und schalte ihn wieder ein.

Warte, bis die Internetverbindung wieder aufgebaut wurde (für gewöhnlich ca. 2 Minuten, Symbol in der Info-Leiste unten rechts) und aktualisiere die Seite (F5 / "Aktualisieren" - Button / Adresse in Adressleiste mit Enter bestätigen). Solltest Du nun eine andere IP-Adresse sehen, verfügst Du über eine dynamische IP-Adresse und kannst mit C) fortfahren.
Falls sich die angezeigte IP-Adresse nicht ändert, verfügst Du entweder über eine statische IP-Adresse oder über eine festgesetzte IP-Adresse. Frage auch bei Deinem Internet-Provider nach, ob Du wirklich eine dynamische IP-Adresse besitzt. Im Falle einer statischen IP-Adresse, bist Du leider nicht in der Lage, einen Reconnect auszuführen.

Solltest Du hingegen nach Aussage Deines Providers über eine dynamische IP-Adresse verfügen, so besitzt Du eine festgesetzte IP-Adresse. Informiere Dich daher auf Google über die Änderung einer MAC-Adresse. Falls auch diese Methode nicht funktioniert, fahre mit G) fort.
C) Überprüfe, ob es bereits Lösungen zu Deinem Router gibt

Durchsuche das Reconnect-Forum nach Deinem Router. Vielleicht hat bereits jemand eine Lösung für diesen gefunden.

D) Überprüfe, ob es bereits ein Skript für Deinen Router gibt

Klicke auf den "Router auswählen" - Button und es wird sich ein Fenster mit über 1000 verschiedenen Routern öffnen. Keine Sorge, in der obersten Zeile "Router Modell suchen" kannst Du nach Deinem Router suchen. Je mehr Informationen Du eingibst, desto kürzer wird die Liste werden.

Wähle den Listeneintrag aus, der am ehesten zu Deinem Router passt. Das Skript wird in einem Popup rechts davon erscheinen. Du brauchst es nicht zu verstehen, klicke lediglich auf "OK" und es wird automatisch angewandt.

Teste das Skript durch einen Klick auf den "Ändere IP" - Button. Sollte der Test erfolgreich verlaufen, so hast Du nun ein funktionierendes Reconnect-Skript.

Gib die Hoffung nicht auf, falls das Skript nicht funktionieren sollte - es gibt vieles, das Du noch versuchen kannst.

Klicke als Erstes auf den Unter-Eintrag "Erweitert" und erhöhe den Wert bei "Auf neue IP warten" auf 180 (3 Minuten). Auf diese Weise hat Dein Router genügend Zeit, den Reconnect zu vollenden. Du kannst den Wert auch weiter erhöhen, jedoch bedeutet dies lediglich, dass Du länger warten musst, wenn der Test fehlschlägt. Gehe nun zum Reconnect-Eintrag zurück und drücke erneut den "Ändere IP" - Button.

Sollte das Skript immer noch nicht funktionieren, gehe zurück zu D) und versuche ein anderes Router-Skript. Möglicherweise musst Du zuerst verschiedene Skripte ausprobieren, bis Du das Richtige gefunden hast.

E) Was ist, wenn mein Router nicht in der Liste vorhanden ist bzw. keines der Skripte funktioniert?

Schaue Dir zum besseren Verständnis des Reconnects **External links are only visible to Support Staff**dieses Video (Deutsch) an. Im Video wird die Methode des Reconnect Recorders erwähnt, ein **External links are only visible to Support Staff**ausführlicheres Video steht derzeit nur in Englisch zur Verfügung. Dieses ist allerdings gut verständlich.
Folgende Schritte werden im Video erläutert:
1. Gebe die lokale IP-Adresse Deines Routers in die Adressleiste Deines Browsers ein und bestätige diese. Dein Browser wird daraufhin die Router-Seite anzeigen, welche in etwa die Form eines Menüs haben sollte.
2. Klicke Dich durch die verschiedenen Optionen, allerdings ohne etwas zu verstellen. Irgendwann wirst Du auch den Benutzernamen des Routers und das dazugehörige Passwort eingeben müssen (einige Router benötigen keinen Benutzernamen). Solltest Du einen Button oder Link namens "Neustart", "IP ändern", "Zurücksetzen", "Verbindung testen" oder ähnlichen Bezeichnungen finden, so merke Dir den Ort der Option.
3. Öffne den JDownloader. Gehe in den Einstellungen zum Reconnect-Eintrag, klicke auf "Erstelle Reconnect Script" und im darauffolgenden Fenster auf "Start". Nun wird Dein Browser automatisch zur Router-Seite navigieren.
4. Klicke nun auf den zuvor gefundenen Button oder Link zum Neustarten des Routers. Der JDownloader zeichnet alle Schritte seit dem Klick auf den "Start" - Button auf und wird nach einem erfolgreichen Neustart des Routers, das heißt einer Änderung der IP, eine entsprechende Meldung anzeigen.
5. Klicke auf "Ja", um das Reconnect-Skript zu speichern.
6. Benutze den "Ändere IP" - Button im JDownloader, um das Skript zu testen.
Sollte der Test erfolgreich verlaufen, so hast Du nun ein funktionierendes Reconnect-Skript.

Siehe auch: Reconnect Recorder

F) Mein Reconnect-Skript funktioniert nicht, was mache ich jetzt?

1. Keine Sorge, es gibt noch weitere Möglichkeiten.
2. Gehe zurück zu E), aktiviere dieses Mal aber den "Rohmodus", bevor Du auf "Start" klickst. Auf diese Weise wird ein noch detaillierteres Skript erstellt, das fast immer funktioniert.

G) Wenn nichts funktioniert

Benutze die (Erweiterte) Suche, um einen eventuell bereits vorhandenen Thread mit Deinem Problem zu suchen. Bedenke dabei, dass die Suchmaschine nur Wörter von einer Länge mit mindestens 3 Zeichen erfassen kann. Aus diesem Grund ist es gerade im Reconnect-Forum empfehlenswert, Google zu benutzen, da wichtige Terme wie "IP" oder manche Router-Modellbezeichnungen nicht benutzt werden können. Um die Google-Suche zu verwenden, begib Dich zu Google und hänge an Deinen Such-Term "site:board.jdownloader.org/forumdisplay.php?f=2" (ohne die "") heran.
Erst dann, erstelle einen neuen Thread im Reconnect-Forum, wähle den Präfix [Skript gesucht] und benenne Deinen Thread entsprechend dem Router-Modell. Beschreibe Deinen Router und die Schritte, die Du bisher versucht hast. Ein Supporter oder anderer Benutzer wird Dir sobald wie möglich antworten.
__________________
Bitte die Regeln lesen! | Please read the forum rules!

REGELN: Bugreports | RULES: Bugreports


Erste Schritte & Tutorials | Self Help Index | Read Me | JD 2 Beta - FAQ

Support Chat

Keep smiling, it's simple!

Last edited by Think3r; 28.04.2015 at 02:36.
  #3  
Old 25.06.2010, 01:00
drbits's Avatar
drbits drbits is offline
JD English Support (inactive)
 
Join Date: Sep 2009
Location: Physically in Los Angeles, CA, USA
Posts: 4,437
Default Important Reminder for Free users

Important Reminder


If you are a free user (freeloader) like me, file hosts will add inconvenience to encourage us to pay for a premium account. The wait between downloads is normal. Slow download speeds are normal. Sometimes having to respond to Captcha challenges is normal. Even getting messages that say the host is busy are normal.

JDownloader helps in several ways.
1) JD allows you to keep an organized list of what you want to download. Files will download in the order you specify when downloading is available from that host, otherwise JDownloader will go to the next host in your download list.

2) by setting the number of downloads to 3-4, JDownloader will almost always be downloading if you have links from enough hosts.

3) for advanced users with the right equipment, JDownloader can change your IP address to help avoid waiting time, but this is not necessary if you follow step 2. You should learn to search for threads and mirrors before you worry about reconnection.

Last edited by Think3r; 25.06.2010 at 01:28.
  #4  
Old 01.07.2010, 06:33
drbits's Avatar
drbits drbits is offline
JD English Support (inactive)
 
Join Date: Sep 2009
Location: Physically in Los Angeles, CA, USA
Posts: 4,437
Default Instructions for Special Routers

Some routers present special problems. For some, we have a list of suggested reading. For others, you need external software.

Some people have indicated that they have a script that works for their router. If you find a script (or instructions) that works for your router, please post a thread in the Reconnect forum with the title "Script for " followed by your router brand, model, and version. For example "Script for D-Link DVA-G3342SD"

D-Link Router Users
Use Google to search for
Code:
site:jdownloader.org "skript" OR "script" "change IP" OR reconnect "dlink" OR "d-link"
Interesting D-Link posts
Script for D-Link DIR-615 (firmware 3.02RU)
Script for dlink-dir-100-fw112
Script for D-Link DVA-G3342SD ( HorstBox )
Script for Tiscali - D-Link DVA-G3670B
Script for dlink-635-reconnect
Script for dlink-dl-524

Last edited by drbits; 01.07.2010 at 09:08.
Closed Thread

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

All times are GMT +2. The time now is 10:51.
Provided By AppWork GmbH | Privacy | Imprint
Parts of the Design are used from Kirsch designed by Andrew & Austin
Powered by vBulletin® Version 3.8.10 Beta 1
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.